Aims: To determine whether alteration of the maxillary central and lateral incisors' length and width, respectively, would affect perceived smile esthetics and to validate the most esthetic length and width, respectively, for the central and lateral incisors. Materials and Methods: Photographic manipulation was undertaken to produce two sets of photographs, each set of four photographs showing the altered width of the lateral incisor and length of the central length. The eight produced photographs were assessed by laypeople, dentists and orthodontists. Results: Alteration in the incisors' proportion affected the relative smile attractiveness for laypeople (n=124), dentists (n=115) and orthodontists (n=68); dentists and orthodontists did not accept lateral width reduction of more than 0.5 mm (P<0.01), which suggests that the lateral to central incisor width ratio ranges from 54% to 62%. However, laypeople did not accept lateral width reduction of more than 1 mm (P<0.01), widening the range to be from 48% to 62%. All groups had zero tolerance for changes in central crown length (P<0.01). Conclusion: All participants recognized that the central incisors' length changes. For lateral incisors, laypeople were more tolerant than dentists and orthodontists. This suggests that changing incisors' proportions affects the relative smile attractiveness.

Aims: Objective of this retrospective study was to evaluate the treatment effects of the MGBM-System (G.B Maino, A. Giannelly, R. Bernard, P. Mura), a new intraoral device to treat Class II malocclusions with no patient cooperation by unilateral or bilateral molar distalization. Materials and Methods: A retrospective study was conducted to compare the pre-distalization and post-distalization cephalograms and dental model casts of 30 patients (15 male, 15 female) with Class II malocclusion treated with MGBM-System. Mean age at the beginning of treatment was 13.3 years (standard deviation 3.3). Angular, horizontal and vertical measurements were recorded to monitor skeletal and dental-alveolar changes. Molar movements in horizontal plane were monitored by making dental measurements on dental model casts. Results: The MGBM-System produced a rapid molar distalization and Class II relationship was corrected in 8 months ΁ 2.05, on average. The maxillary first molars were distalized of 4.14 (PTV-6 cemento-enamel junction), associated with a significant distal axis incline of 10. 5° referred to SN and a significant intrusion of 1.3 mm (PP). As for anchorage loss, the first premolar exhibited a significant mesial movement of 0.86 mm, associated with a significant mesial axis incline of 2.46°. No significative changes in either sagittal or vertical skeletal relationship were observed. Conclusion: The results suggest that the MGBM-System is an efficient and reliable device for distalizing the maxillary permanent first and second molars.

Objective: To assess the mesio-distal tooth width in normal, crowded, or spaced dentitions. Materials and Methods: A sample of 192 maxillary and mandibular dental casts of Libyan subjects was selected from a larger cohort. These subjects did not present with craniofacial anomaly, hypodontia, significant attrition, caries, restorations, or history of permanent tooth extraction or orthodontic treatment. The sample was divided into normal, crowded, and spaced groups according to tooth size/arch length discrepancy. Each group included 32 upper and lower dental casts with equal numbers of males (mean (SD) age = 14.7 (1.9) years) and females (mean (SD) age = 15.7 (2.5) years). The mesiodistal (MD) tooth width, sum of the MD tooth widths mesial to the first molars (TTM), sum of the MD width of the four incisors (I), and the sum of the MD width of canine and first and second premolars (CPP) were calculated for each group. The independent Student t-test was applied sequentially to detect significant differences between paired groups. The ANOVA test was undertaken to explore significant differences between the three groups. Pearson coefficient of correlation was used to evaluate the correlation between I and the corresponding CPP in maxillary and mandibular arches. Results: MD tooth width, TTM, I, and CPP were significantly wider in the crowded compared to normal and spaced dentitions (P<0.001), except for the width of the upper left lateral incisors in both normal and crowded groups. Although there was a trend for smaller tooth widths in spaced dentitions compared to normal ones, this was only significant in the maxillary left central incisor, maxillary right and left lateral incisors, maxillary right first premolar, mandibular right lateral incisor, and mandibular right canine (P<0.05). However, the maxillary TTM, I, and CPP in the normal group were significantly greater than in the spaced group (P<0.05). Significant positive correlations existed between the mean values of I and CPP in both the maxillary and mandibular dentitions of all groups (P<0.01). Conclusions: It appears that in the studied Libyan population, the MD tooth width is a significant component of crowding/spacing.

Aim: To determine the efficiency of erbium: Yttrium aluminum garnet (Er:YAG) laser with Environmental Scanning Electron Microscope (ESEM) and shear bond strength analysis as a method of recycling stainless steel orthodontic brackets and compare with other methods of recycling. Materials and Methods: Eighty samples of extracted premolar teeth bonded to SS brackets were tested for rebonded shear bond strength after recycling by four methods and compared with a control group of 20 samples. These 80 samples were randomized into four groups which were recycled by four methods, namely, sandblasting, thermal method, adhesive grinding by tungsten carbide bur, and Er: YAG laser method. After recycling, ESEM and shear bond strength analysis were used to analyze the efficiency of the recycling methods Results: Er: YAG laser group was found to be having the greatest bond strength among the recycled brackets (8.33±2.51 followed by the sandblasting at 6.12±1.12 MPa, thermal and electropolishing at 4.44±0.95 MPa, and lastly the adhesive grinding method at 3.08±1.07 MPa. The shear bond strength of Er: YAG laser group was found to be having no statistically significant difference with that of the control group (P>0.05 and had statistical signifance with sandblasting, thermal and electropolishing and adhesive grinding groups at P>0.001. ESEM analysis showed complete removal of adhesive from the brackets recycled with Er: YAG laser which mimicked that of the control group. Conclusion: Er: YAG laser (2940 nm) was found to be the most efficient method for recycling, followed by the sandblasting, thermal, and the tungsten carbide methods, which had the least shear bond strength value and is not fit for clinical usage.